Vehicle Cleaner for the Pros

HOW TO USE PRO TIPS!

Bugs N All uses a unique formula that neutralizes the hard acid shell that makes Bug Splatter so difficult to clean off. Once the acid shell is neutralized, the rest of the formula is able to penetrate the organic matter. The releasing process quickly softens and in many cases begins to carry away the grime. Once the releasing process is complete, it is very simple to wipe away any dirt, grime, or bug guts; Revealing the shiny surface you knew was there.

There are three basic steps in order to be successful when using Bugs N All.

1. Wet it & Wait

2. Wipe it & Rinse

3. Dry it - DONE!

But we're going to break the process down for you even further. Then we'll give you some ultimate Pro Tips. And finally, we'll talk about some specialty cleaning uses for Bugs N All.

Let's start with the basics.

Step 1: Gather Supplies

Whether you're detailing the interior or giving the exterior a bath, You'll need to gather the supplies you normally need for cleaning your vehicle. For the purpose of this illustration, we'll be preparing for washing the exterior of the vehicle.

Prepare by gathering a wet towel, and or bucket of water with a bug sponge, dry towels, or car washing brush. If you intend on cleaning the entire vehicle you may want to add some car washing soap to your bucket of water. Grab a garden hose for rinsing or use another bucket and towel for rinsing.
Step 2: Spray it on!
Step 3: Wait

Wait! This is where people have the most trouble. Bugs N All is working as long as the surface is wet with Bugs N All solution. So, just be patient and allow Bugs N All to do its job.

How long do I need to wait?

We recommend waiting a minimum of 30 seconds and sometimes up to 2 minutes. The time needed depends on many factors. But the main factor is the thickness of the splatter or grime.
Step 4: Test
Step 5: Wipe
Step 6: Rinse
Step 7: Dry

After a good rinse, we recommend drying the vehicle with a soft highly absorbent microfiber towel. This will help prevent water spots and any possible streaking. While streaking is not common, It can occur if the area was not rinsed shortly after being cleaned and the area had a chance to dry before rinsing.

If streaking does occur, simply rinse the area with a wet towel followed by drying.
Step 8: Admire a Job Well Done!

PRO TIPS

The purpose of this section is to give you Pro Tips that will help guarantee your success while using Bugs N All. Some of these tips come from customers who have found innovative ways to make the job even more simple.

If you find a great way to use Bugs N All, shot a video, and send it to us at Support@procelle.com. We may feature your Pro Tip and give you all the credit.

Let's dive in.

Use It In The Shade: The hot sun will evaporate liquids quickly. To get the most out of your Bugs N All, apply BNA in a shaded area or where the surface is cool to the touch (whenever possible). Bugs N All will not harm the surface if it dries or evaporates. Simply reactivate it by spraying on more Bugs N All solution.

If you have to clean the vehicle in the hot sun, spray a liberal amount of Bugs N All over the area. Apply more solution to the surface as needed.

Lay a wet towel over the area soaked with Bugs N All and prop it up if possible. This will help keep Bugs N All wet longer. Use a broom handle to prop the towel in place if needed. It’s best to use BNA in the morning, in the shade, or on a cloudy day to minimize evaporation.

Let It Work: Don't speed the process! Bugs N All needs time to break through the acid shell before turning grime into mush. To test the releasing process, gently rub on a spot to determine whether when the full release has occurred. If you can easily rub them off with your damp towel, they are ready to easily wipe off.

For particularly difficult cleaning challenges. Try, the following:

Make sure to keep Bugs N All wet on the stubborn spot for at least 2 minutes.
Be sure the ambient temperature is above 60 degrees F.
Bugs N All will not remove wax, So it is possible the spot has been waxed over during previous washings. Thus causing the difficulty. If this occurs, wash the vehicle several times without applying any wax. Don't use a washing solution that contains wax.
It is possible that the stain is etched into the clear coat. In which case Bugs N All will not be able to remove the stain.
Move the vehicle into direct sunlight to warm the vehicle's surface. Keep Bugs N All wet by reapplying several times until the surface has released.
On rare occasions, scrubbing is all you can do. During some times of the year, the acid content inside bugs, and some grime increases. Bugs N All's formula is balanced to handle the average bug acid content. In these cases, Bugs N All will remove the bug splat or grime in layers. Reapplication would be needed.

Use Above 60 Degrees F.

The ambient temperature should be above 60 degrees F for Bugs N All to work. We recommend a good temperature range of 60 - 85 degrees F. Humidity does not seem to affect the performance of Bugs N All. However, if the temperature gets too hot, the product will evaporate before it has had a chance to work. Refer to Pro Tip - In The Shade.

Waxed Over

Bugs N All will not remove wax. If you have washed your vehicle with a cleaning solution that also contains wax, it may be difficult to remove the remaining bug splatter, black streaks, oxidation, or other grime. Any gunk that has a layer of wax on top will require some scrubbing.

Don't Freeze It

We highly recommend keeping Bugs N All away from freezing temperatures. We are concerned only about the bottle or sprayer breaking. The solution will not be harmed in any way.

Tools To Use

Use whatever tools you currently use to wash your vehicle. You can use a regular car washing brush, micro-fiber cloth, bug sponge, a washing mitt, semi-hard bristle brush (for cleaning roofs and awnings), or a bath towel. Use good common sense and avoid heavy abrasives on sensitive surfaces.

Important: We recommend your tools like towels, sponges, and brushes are dripping wet when wiping or scrubbing any scratchable surface.

Rinsing and Drying

Rinsing soon after cleaning the area followed by drying can help reduce water spotting and streaking.

Bugs N All Specialty Uses

RV Awnings

Cleaning the awning on campers presents a unique challenge. They are often high and difficult to reach. The best method to clean awnings is to fully extend the awning or position it where it is best reached. Use a long handle brush when agitating the fabric. Spray a liberal amount of Bugs N All on the highest point of the awning. You can expect to get a bit wet. You may want to wear safety glasses to protect your eyes from grime.

Allow the solution to run down the top surface ensuring the entire surface is wet roll the awning up and let sit for 10 minutes. This will keep the solution and fabric wet while it is working to release the grime.

After 10 minutes of rest time, unroll the awning and begin scrubbing with a medium stiff bristle brush. After the entire upper and low portions of the awning have been agitated, rinse both sides with water.

Touch up where needed and allow the awning to dry before stowing it away.
Removing Black Streaks and Oxidation
In The Shade: So that you get the most out of your Bugs N All, we recommend you apply BNA in a shaded area or where the surface is cool to the touch. It will not harm anything if BNA dries. Simply reactivate it with water. Besides, you only use more BNA when evaporation increases due to surface and ambient temperatures.

Let It Work: It usually only takes about 20 seconds to release Black Streaks from Aluminum and Fiberglass surfaces. However, it sometimes takes up to 2 minutes for BNA to release Black Streaks.

Keep It Wet: Keep the area wet until full penetration has occurred.

Oxidation: Bugs N All will not remove wax. However, If the surface is oxidizing, then there is no wax left on the surface. After cleaning and removing Black Streaks and Oxidation, use a premium wax to help prevent oxidation.

Black Streaks: Black Streaks are caused by pollutants in water which leaves deposits on the surface. After it dries it becomes hard. A great way to help prevent Black Streaks is to keep the roof clean.

.
Leather Cleaning

Cleaning leather is really straight forward. Spray on, let sit for a few seconds and wipe with a clean dry towel. If Bug Splatter is on leather chaps, saddlebags, or coats, spray Bugs N All on and allow it to remain wet for about 30 seconds. Wipe and repeat as needed. A soft brush may be useful with gentle pressure to aid in cleaning and getting into the pores. Refer to the manufacturer's instructions prior to using Bugs N All. However, Bugs N All is safe to use on most leather products.
Airplane Cleaning
Start Smart: Start by cleaning your aircraft in a well-shaded area or when the sun is not beating down on it. You will get the best results when it is cool to the touch. If Bugs N All drys simply reactivate it with water.

Using Bugs N All: Spray a liberal amount of Bugs N All on the surface to be cleaned.

Time is Your Friend: Allow Bugs N All to work at releasing the Bugs, grease, and grime from your plane. It may take as little as 10 seconds and sometimes up to 2 minutes for BNA to completely release grime. Give it time and you will love how easy it is for you. To test the area, use your finger, by gently rubbing over the soiled spot. Once that spot releases with your finger you can then easily clean the area with a brush and water.

Cleaning The Interior: Spray a mist on a towel and wipe down the instrument panel. Spray on seats or other areas and wipe with a dry towel.

We recommend diluting Bugs N All for cleaning the interior windows: add 1/8 cup Ready-To-Use Solution to 1 quart of water into another sprayer. This will eliminate the risk of streaking or smearing on the windows.

Cleaning Exterior Windows: Spray a liberal amount of Bugs N All on the exterior windows and allow Bugs N All to completely penetrate grime and bugs. This usually takes 1-2 minutes. Use a sponge with water or whatever method you use to clean the windows.

Removing Grease: Spray Bugs N All on and allow time to penetrate. Then wash and rinse normally.
Boat and Marine Cleaning
Start Smart: Start by cleaning your boat in a well-shaded area or when the sun is not beating down on it. You will get the best results when it is cool to the touch. If Bugs N All drys simply reactivate it with water.

Using Bugs R Gone: The best way we have found to clean is to get a pump-up garden sprayer. Place BNA Ready-to-Use in the garden sprayer, spray a small section, and using a vehicle washing brush and a bucket of plain water, wash, rinse and dry. Depending on how soiled the surface is, you may want to pre-rinse the area before spraying Bugs N All.

Time is Your Friend: Allow Bugs N All to work at releasing the Bugs, Fish Scales, Water Scum, and grease from your boat. It may take as little as 10 seconds and sometimes up to 2 minutes for BNA to completely release grime. Give it time and you will love how easy it is for you. To test the area, use your finger, by gently rubbing over the soiled spot. Once that spot releases with your finger you can then easily clean the area with a brush and water.

Cleaning Boat Hull and Bottoms: Using the Garden sprayer, sprayer a generous amount of Bugs N All on small sections. Wait for about 2 minutes while keeping the area wet with BNA. Use a hard bristle brush, brush the area, and then rinse with water. Repeat as needed.

Cleaning Vinyl and Carpet: Spray Bugs N All on vinyl and allow time to penetrate. Then use a soft brush and water to wash the area. Repeat as needed. Note: Some older boats may have permanent mildew stains. Bugs N All will help to lighten those stains.

Cleaning Fishing Equipment: The best way to clean fishing equipment with Bugs N All is to spray BNA on a towel and wipe the equipment off. Remove water spots from windshields and electronic equipment using this method works great.
RV and Camper Cleaning
Start Smart: Start by cleaning your motor coach in a well-shaded area or when the sun is not beating down on it. You will get the best results when your camper is cool to the touch. If Bugs N All drys simply reactivate it with water.

Using Bugs N All: The best way we have found to clean the exterior is to get a pump-up garden sprayer. Place BNA Ready-to-Use in the garden sprayer, spray a section in the camper, and using a vehicle washing brush and a bucket of plain water, wash the vehicle, rinse and dry. Depending on how soiled the surface is, you may want to pre-rinse the area before spraying Bugs N All.

Time is Your Friend: Allow Bugs N All to work at releasing the Bugs, Black Streaks, Oxidation, and Grease from your RV. It may take as little as 10 seconds and sometimes up to 2 minutes for BNA to completely release Bugs. Give it time and you will love how easy it is for you. To test the area, use your finger, by gently rubbing over the soiled spot. Once that spot releases with your finger you can then easily clean the area with a brush and water.

Cleaning Camper Roofs: Using the Garden sprayer, sprayer a generous amount of Bugs N All on small sections of the roof. Wait for about 2 minutes. Use a bristle brush to brush the area and then rinse with water. Repeat as needed. As always, be careful of tripping hazards.

Cleaning Awnings: Pull the awning out and Spray Bugs N All on until it is completely wet. Roll it back up and wait for 10 minutes. Unroll the awning and brush the surface, rinse with water and allow it to dry. Note: Some older awnings may have permanent stains that cannot be removed.
Interior Detailing
Cleaning Vehicle Carpeting: The carpet in your vehicle is rather tough and it takes a lot of abuse over its lifetime. Cleaning this area of the car or truck is pretty straight forward. Spray BNA on the surface and allow a minimum of 10 seconds (and sometimes more than 2 minutes) to work. Use your finger to wipe the area to see how fast BNA is working to determine whether more time is needed before removing the stain. As long as the carpet is wet with BNA, the product is working. In many cases, removing the stain means simply using a towel and wiping the area dry. Other stains may need a more aggressive approach, so consider using a brush to help loosen up the stain. In any case, use common sense. BNA will remove most stains.

Cleaning Dash Boards: Spray a lite mist of BNA over the dashboard area. Concentrate on cleaning half of the dashboard at a time. Wipe the area cleaning with a dry towel of your choice. If there are heavily soiled areas spot clean or spray a heavy mist on a towel and cover the soiled area with the wet towel for 30 - 60 seconds before wiping.

Cleaning Window and Mirrors: If streaking occurs while cleaning the interior windows and mirrors, consider diluting BNA by using another sprayer. Dilute the ready to use solution by 1/8 cup per .32 ounces of water. Continue to dilute as needed until no streaking occurs. Here is one important tip. Clean the windows and mirror in a shaded area. The sun evaporates the fluid too quickly, which also contributes to streaking and smearing.

Cleaning The Seats: Cleaning the seats is similar to cleaning the carpet. Spray on the seat allow about 10 seconds for the product to work before wiping. This method applies to leather, vinyl, fabric seats, booster seats, and car seats.
De-Greaser
In The Shade: So that you get the most out of your Bugs N All, we recommend you apply BNA in a shaded area or where the surface is cool to the touch. It will not harm anything if BNA dries. Simply reactivate it with water. Besides, you only use more BNA when evaporation increases due to surface and ambient temperatures.

Let It Work: Don't be speedy Gonzales! Bugs N All needs time to break through the grease proteins. Allow a minimum of 10 seconds to 2 minutes to penetration. It may be necessary to use a brush to aid in the penetration and lifting of grease.

Keep It Wet: Keep the area wet until full penetration has occurred.

Warm it Up: Bugs N All penetrates grease best in warm temperatures.
General Cleaning and Stain Removal Tips
In The Shade: So that you get the most out of your Bugs N All, we recommend you apply BNA in a shaded area or where the surface is cool to the touch. It will not harm anything if BNA dries. Simply reactivate it with water. Besides, you only use more BNA when evaporation increases due to surface and ambient temperatures.

Let It Work: Allow a minimum of 5 seconds to 2 minutes for full penetration.

Keep It Wet: Keep the area wet until full penetration has occurred.

Use Other Tools: It's OK to use Microfibers, Brushes, Blotting Techniques, scrubbing, and so on to cleaning and remove stains. Just use your best judgment and test Bugs N All first on delicate areas where you may not be sure how BNA will handle your cleaning efforts.